Home > Zone 2 > Onkyo Hdmi Sub Out Not Working

Onkyo Hdmi Sub Out Not Working

Contents

I just tried what you said and it still doesn't work. A couple of months ago he calls me wanting to make the jump to an HDMI receiver. Was 1080p/ 24 also supported on the previous TV? - FMs ForumMod1 offline Site Admin Posts: 6351Joined: Tue Dec 11, 2012 4:57 pm Top Re: No Video on Main HDMI Out, If I had to pick a likely culprit, it be this last thing. check over here

Register for an account Please read the following: Unsolicited commercial advertisements are absolutely not permitted on this forum. This sweepstakes ends on November 17, 2016. Speaker Systems TV Speaker Systems Bluetooth Speakers Accessories Headphones Headphone Amplifiers Applications Support Support for your Onkyo product. But it's weird how the TX-NR535 didn't have this issue(even though it only has 1 hdmi out).

Onkyo Tx Nr626 Hdmi Sub Out

ENTER HERE © CBS Interactive Inc.  /  All Rights Reserved. Hi guys, I just bought a Onkyo 1008 purely for the Dual HDMI out to save me manually swapping cables between TV and Projector. Hello everybody.I got the subwoofer to work for around 5 days or so.

This would also be the case using one of the above AVRs as well. Yes, I bought some fancy speaker wire, but in retrospect I'm not sure that I would do it again. All submitted content is subject to our Terms of Use. Onkyo 646 Zone 2 Now I have to disconnect everything, box it up, drive to store and return.

The receiver is an Onkyo TX-SR674 with the KEF 2005.2 speaker and subwoofer set. Onkyo Tx Nr626 Zone 2 Not Working but wouldn't a HDMI amp/splitter (1 in/2 out) sort this out? You could eliminate the need to go from the receiver through the matrix for that room. http://www.remotecentral.com/cgi-bin/mboard/rc-custom/thread.cgi?29529 hollywoodzuhause 174.987 visualizaciones 59:07 Onkyo TX-NR626 receiver (Unboxing and sound test) - Duración: 3:30.

Even thought it's Monoprice, I don't think it's the switch. Onkyo Zone 2 Hdmi When displays are switched off (or disconnected and reconnected), EDID can be lost and a computer or a Hi-Def video device can lose its ability to properly display the image. " Reply OP | Post 8 made on Saturday October 27, 2012 at 22:01 Craig Aguiar-WinterAdvanced Member Joined:Posts:September2002927 View Profile Great idea, Golenzrule.Now to find a wholesaler in the Toronto area that Acción en curso...

Onkyo Tx Nr626 Zone 2 Not Working

HDCP and EDID HDMI is not just a connection you plug in like an RCA, where once you have continuity, you have a picture.HDMI is more like a network connection as http://forums.whirlpool.net.au/archive/1723123 I installed an Onkyo TXNR-616 into the system. Onkyo Tx Nr626 Hdmi Sub Out But check this by using a cable that you KNOW works before you go out spending more money...(that's just the cheapskate in me talking...)Best,Ben Flag Permalink This was helpful (0) Back Independent Zone 2 Hdmi Output Receiver I haven't seen this config anywhere?

by ..ben / October 1, 2007 5:21 AM PDT In reply to: Cable Switch out the cable with one of your plain old RCA cables between a source and the receiver, http://cestudios.net/zone-2/onkyo-609-zone-2-not-working.html After around a month or so when I began playing around with settings, the subwoofer suddenly gets no more signal from the receiver. A regular ol' RCA cable WILL work in a pinch for a LFE Out connection. Instant gratification: PCM will ONLY do 2.0-ch over Optical, and DTS-HD MA will give you improved 1.5Mbps stream and works fine over Optical.Hopefully this helps. Onkyo Zone 2 No Sound

Anyone with any experience with Onkyo Dual HDMI output settings care to share some wisdom on the matter? Siguiente ONKYO How to set up zone 2, use of Remote App (multizone Remote App Android) - Duración: 4:10. Onkyo USA Corp. this content I also have a PlayStation 3 hooked up with digital optical sound.

Defective AVR? Hdmi Audio To Zone 2 I have checked all of the physical connections and all of that is fine. When clicking display, it shows MCH PCM 5.1 and 3440x1440p/60 on the receiver.

Examples include home theater audio-visual receivers that separate and amplify the audio signal, while re-transmitting the video for display on a TV. " (or what a HDMI splitter would do, hence

My friend hasn't replied back to me yet with the result of the bypass (which could take a couple of weeks like last time), and I sent an email to Onkyo. He says it worked and that the unit shows latest firmware installed when he tries to update again.At any rate he says it's working fine now.Thanks again for the post.Craig My until last night when he called me again with the same problem. Onkyo Zone 2 Trick What's weird is, if I use the second HDMI out(SUB) on the receiver, the PC input shows video fine.

As the on screen display is only displayed on the HDMI MAIN OUT terminal and NOT the HDMI SUB OUT terminal; this would explain why you are not seeing the OSD Disruptive posting: Flaming or offending other usersIllegal activities: Promote cracked software, or other illegal contentOffensive: Sexually explicit or offensive languageSpam: Advertisements or commercial links Submit report Cancel report Track this discussion Ive noticed that with the 'both setting' its the TV that has the issues the projector always displays a picture. have a peek at these guys Amplifier/Receiver CD-Player Network Audio Player Tuner Turntables Speakers Reliable partners for your Onkyo system.