Home > Oil Pressure > Oil Pressure Gauge Not Working Rx7

Oil Pressure Gauge Not Working Rx7

Contents

I bought the car with this issue, though I didn't know about it until I investigated further more recently. all starting and fuel system sensors check out good. There has to be something. used at least 4 wraps teflon tape + 7/16 Alum StatoSeal (Pegusus 3245-7/16) at sender Drilled and cut an alum. http://cestudios.net/oil-pressure/oil-pressure-gauge-not-working.html

Who knows for sure about this? ______________ Date: Wed, 7 Jun 2000 19:02:02 -0700 (PDT) From: RETed ([email protected]) The oil bypasses the rotor bearings (well, very little gets to the rotor Also remember that indicated pressure is a function of the viscosity rating of your oil, engine temp, ambient temp and in these cars, some fuel dilution between oil changes. Justin Fisette 13,932 views 2:44 Loading more suggestions... as the car heats up .. http://www.rx7club.com/new-member-rx-7-technical-256/fc-oil-pressure-gauge-failure-932829/

Rx7 Oil Pressure Sending Unit

I don't have an FD but I can't imagine they changed the oil pressure sender connectors that much. it went to the correct pressure and next time i went to drive it, it was no longer working. Attach the other end to a new stock sensor. The two temp/resistance values in the FSM are: 50C - 154 ohms 130C - 12 ohms 07-17-12, 11:03 PM #5 BorinquenRotary Junior Member Thread Starter Join Date: Jun

angle to hold sender to tower. Any ideas or help would be great. Maybe this was just a fluke and the gauge didn't want to work today. 10 commentsshareall 10 commentssorted by: besttopnewcontroversialoldrandomq&alive (beta)[–]pilgrimz 2 points3 points4 points 1 year ago(5 children)Maybe the cable came off? Loading...

The sender could be OK, and you could have a serious problem such as a bad oil metering pump. --Steve June 07, 2000 _________________ Mine went from showing ~90 - 100 You will love driving it!! Tem120 View Public Profile Find More Posts by Tem120 View iTrader Profile 02-19-12, 05:04 PM #17 arghx rotorhead iTrader: (3) Join Date: Aug 2004 Location: cold Posts: 14,921 as it warms up it lowers to 20 when I give it some gas it goes to 60 then lowers to 10.

Throwing this vid up to help guide ppl doing the same modifications. Thanks. Working... breakfast View Public Profile Find More Posts by breakfast View iTrader Profile Related Topics Thread Thread Starter Forum Replies Last Post [For Sale] JDM 2002 Instrument Cluster - White

Rx7 Fc Oil Pressure Sender

I changed the oil a week ago , and the car hasn't been driven one mile so Idont think its that. https://www.reddit.com/r/RX7/comments/36xpf6/bad_oil_pressure_gauge_or_am_i_screwed/ Password Register Forgot Password? Rx7 Oil Pressure Sending Unit You can read about them here.X LinkBack LinkBack URL About LinkBacks NoPistons -Mazda Rx7 & Rx8 Rotary Forum > Mazda Rotary Generation Specific > 2nd Generation Specific Oil Pressure Gauge Rx7 Oil Pressure Sensor Several people have reported going through 2 or 3 of the senders by 50K miles.

The needle never moves, however I have been able to trigger the warning light when the oil level is extremely low. have a peek at these guys The fitting shown as well as the sensor both have tapered threads. And visa versa. permalinkembedsaveparentgive gold[–]PerfectlyAwful[S] 0 points1 point2 points 1 year ago(3 children)Never mind, found some pictures online.

The time now is 11:44 AM. -- 37-RX7-Lite -- 37-RX7-Dark -- Classic Next Gen Contact Us - RX7Club.com - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Make It Mike 18,208 views 3:02 Rx7 fd3s startup after t04r install - Duration: 2:23. The risk of a burst pressure line is no different than any of the other oil cooler lines. http://cestudios.net/oil-pressure/oil-pressure-gauge-not-working-dsm.html Took only 15 or so minutes.

Custom color67 points · 11 comments My old 2000 RB, great cars!5 points · 3 comments RX-7 UIM ground for ecu.11 points · 10 comments The SCCA Racecar FC I bought.21 points · 7 comments The new 2011 Mazda You should see the needle on the gauge move part of the way up relative to the resistance. 30 psi - 197 ohms 60 psi - 141 ohms 110 psi - When the gauge works properly, it is easy to note small changes in level by looking at the pressure.

You may try just cleaning the connection with some sand paper or steel wool first.

If that line bursts you've got a BIG pressurized oil mess. also make sure that the ground is clean mike 03-15-2003, 03:01 PM #36 Shane.Trammell Senior Member Join Date: May 2002 Location: Richardson Texas Posts: 4,326 Rotary Year: n/a Related Topics Thread Thread Starter Forum Replies Last Post [For Sale] JDM 2002 Instrument Cluster - White Faced / Amber Illumination MattGold 3rd Generation RX-7 (1993-2002) Parts 5 08-24-15 08:58 AM Fixed the gripe and buttoned everything back up.

I think less frequently it's the sender. Agreed arghx View Public Profile Find More Posts by arghx View iTrader Profile 02-19-12, 06:15 PM #18 Sgtblue Viable fossil iTrader: (8) Join Date: Oct 2003 Location: Transcript The interactive transcript could not be loaded. this content I started the car and the readings mirror'd the oil pressure sensor / gauge on my car ..

What I ended up doing most recently was dropping the oil pan and checking the regulators and pickup tube/screen. They are easily disabled if you care to do so (as I have done in my aircraft 20B engine build up, and on other 13 engines I have rebuilt). No, it doesn't mean you shouldn't idle the car. Thanks. 07-16-12, 03:07 PM #2 RotaryRocket88 Top Down, Boost Up iTrader: (7) Join Date: Mar 2008 Location: San Diego, CA Posts: 8,719 Are you positive the water

Before I start in on this little >project, has anyone tackled these subjects yet? Rating is available when the video has been rented. Loading... They fit perfectly into the standard gauge position, thus giving you the option of displaying 6 channels without the need to fill up the car with loads of pods They are