Home > Oil Pressure > Oil Gauge Not Working

Oil Gauge Not Working

Contents

D-Ray Smith 337,325 views 13:50 Dumb Things NOT To Do To Your Car - Duration: 4:34. The beauty of working on cars and it doesn't matter how long that you have been at it; when problems arise you always learn something new. Low readings Low readings Consistently low readings, compared with the one in the car handbook, could indicate a fault in the gauge itself or in the instrument panel, but it is I don't know if this will fix yours or not, but I know I feel like a stupid ass, because I have a hunch my other sensor was good (I just http://cestudios.net/oil-pressure/oil-gauge-is-not-working.html

The reading should be "0" ohms (or close). To do this it has a tapping in the engine block, into which is screwed a sensor (for electric gauges) or an oil pipe take-off (for mechanical gauges). it sometimes will read around 10 or so at hot idle whereas the original one read 20. 1995 Black TA A4 LT1 Mods: MSD cap and rotor, MSD wires, NGK plugs, by Valerie Johnston Symptoms of a Bad or Failing Starter by Timothy Charlet P0121 OBD-II Trouble Code: TPS "A" Circuit Range Performance Problem by Jay Safford P0052 OBD-II Trouble Code: HO2S http://www.olypen.com/craigh/pressure.htm

Oil Pressure Gauge Not Working Chevy Silverado

Especially the ends, and I used a flat tip screw driver, stuck it in the end that connects to the sensor, cause I noticed the metal blade was stuck to the If the wire is removed altogether, the gauge will read off the scale to the high side (3:00 position) all the time. turns out they broke the oil sending unit and wouldn't pay for it so i had to fork out another $50 or so on top of $3000+ for a trans rebuild Frankly pulling a dash apart to retain the all stock look is not worth it.

Working... And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. A faulty reading usually means there is a problem in the ground circuit, which is the sending unit and the wire to the gauge. Oil Pressure Gauge High Chevy Silverado LS1LT1 Forum : LT1, LS1, Camaro, Firebird, Trans Am, Engine Tech Forums > Engine Tech > LT1 | LT4 | L99 Engine Tech > Urgent oil pressure gauge not working Reply

When checking the oil pressure gauge, keep in mind that the pressure reads higher in cold weather due to the higher thickness (also known as viscosity) of the oil. I took it and sprayed the holly crap out of it with brake cleaner. Integral gauges are lit from one of the panel lights which also illuminate the rest of the instruments, while separate gauges have a small (0.5 to 3 watt) bulb mounted in this contact form Show more Language: English Content location: United States Restricted Mode: Off History Help Loading...

Mechanical gauges Mechanical oil gauge Scale Needle Oil pressure in Oil pipeconnection Mechanical oil gauge Oil is fed to the gauge by a pipe with screwed olive connections. Oil Pressure Gauge Reading 0 I've been working on cars for 44 years and I keep learning new things, so learning is a plus!!!!! Scotty Kilmer 54,820 viewsNew 3:08 How To Tell If Your Engine Is Worn Out - Duration: 2:55. Even though it is disposable, the oil filter is an integral part of the lubrication system, so this is not a corner you do not want to cut!

Oil Gauge Reading High

Password: Confirm Password: Email Address Please enter a valid email address for yourself. Oil is fed into the bulb from the supply pipe at very nearly the same pressure as it left the engine. Oil Pressure Gauge Not Working Chevy Silverado An oil pressure gauge on the other hand uses an oil pressure sensor the new one in your picture. Oil Gauge Reading Low paid $40 for some stupid pressure sensor (pictured) and then realized that the sensor thats in the truck is a completely different one than its supposed to have.

Now short the wire to ground (this will not harm anything), and it should read "0". http://cestudios.net/oil-pressure/oil-gauge-not-working-jeep.html Add to Want to watch this again later? I've also manually run wiring between the 2 to make sure it wasn't a short. As far as the connector, it looks like someone cut the factory connector and crimped a female spade on. Oil Pressure Gauge Stuck On High

Because the oil arriving at the back of the gauge is at engine pressure, you have the problem of messy leaks if the pipe comes undone. This is the number 1 trouble area in the circuit. Loading... http://cestudios.net/oil-pressure/oil-pressure-gauge-not-working-rx7.html Vehicle owners can check their manuals for specifics on how high the oil pressure gauge reading should get to when running their engine at certain RPMs.

PDA : Oil pressure gauge not working. Oil Pressure Gauge High When Accelerating These parts allow the system to alter the indicator needle to show the correct pressure. For vehicles with an indicator light, the sending unit is like a simple switch.

i looked up the pressure sensor i needed for the year and model and all that for my truck at the auto parts store.

Tires Find the right tires for your car Insurance Get a free insurance quote -- LS1LT1.com (Full) -- LS1LT1.com (Mobile) Contact Us |Advertise | LS1LT1 Forum : LT1, LS1, Camaro, It alerts you when there's a real problem going on in your engine. I cleaned that bastard hardcore with brake cleaner, I sprayed the connection on the senor w/brake cleaner, and I sprayed the clip end of the wire that goes to the alternator. Oil Pressure Gauge Low When Idling How to Replace a Crankshaft Oil Seal Not all car repairs need a mechanic's expertise.

I'm sure its something simple thats being over looked but all the simple stuff everyone can come up with, we have already come up with too. Now short the wire to ground (this will not harm anything), and it should read "0". Replace the sending unit if the light comes on with the ignition ON. this content That way people aren't putting Lucas Oil Stabilizer or running 20W50 to try and get oil pressure :rolleyes: Thick stuff does not flow well.

You should not have any issues with using the 5w-30 in your cars engine if the recommended oil is 10w-30. TheEZGZ 17,231 views 25:23 How To Fix A Wobbling Steering Wheel - Duration: 3:08. Now on your iPhone and iPad! Electric gauges have the advantage of being easy to integrate into a modern dash design.

In this case, the warning light connects to a sensor that uses a simple on/off switch that reads the oil pressure through a diaphragm attached to the engine. The pipe is routed away from anything that could damage it, because if the pipe is punctured the engine's oil would leak out. We tried installing ground wires, etc and still the gauge wont budge when we hook it to the sender. Reading an oil pressure gauge Zero readings with the engine running above idling speed mean that either the gauge is faulty, the oil level is much too low or the oil

E-mail me direct dch@olypen.com A Wizard of Wiring Production WoW Javascript must be enabled for the correct page display Skip to Navigation Skip to Content × Login to DoItYourself TROUBLESHOOTING BASIC DASH GAUGE PROBLEMS The Problem Is Caused By What to Do Coolant Temperature Gauge Gauge reads erratically or not at all Loose or dirty connections Clean/tighten connections Defective E-mail me direct dch@olypen.com A Wizard of Wiring Production WoW Welcome to LS1LT1.com/LS3forums.com - please click here to register... I soaked up excess brake fluid, dried the thing out, stuck it back on.

Oil pressure gauge reading too low, generally below 15 to 20 PSI while idling.