Home > Not Working > New Hid Bulb Not Working

New Hid Bulb Not Working

Contents

If the flickering is caused by the DRL you can try a wiring harness or have the DRL disabled (NOTE: disabling the DRL may not be legal in all areas, check If that's not the source of the problem, check the bulb itself for any damage or interference. Add to Want to watch this again later? I just lit up my HIDs for the first time since I installed the 15 amp. Source

To perform this test, please swap your bulbs to opposing sides and note what happens to your kit. If this is the case, you may have a defective bulb or ballast. My HID Bi-Xenon high beams or low beams are not working or are inverted. Sign in to report inappropriate content. http://www.xenonhids.com/troubleshooting-guide.html

Hid Headlight Problems

The easiest way to check this is by swapping the bulb and ballast one at a time to the side that works to check that each component is functioning as it Guillaume Tweet Remove Advertisements Sponsored Links 8th Generation Honda Civic Forum Advertisement 03-30-2009, 07:39 PM #2 (permalink) Poweraide Senior Member Join Date: Jan 2009 Location: ATL Note: Reverse Polarity is an issue with the cars wiring not the HID kit.

If your car has Daytime Running Lights (DRLs), the reduced operating voltage of the DRLs is likely responsible for the flickering; the problem may be corrected by pulling the fuse for This is often a normal adjustment. I only turn the HIDs ON when the engine is running. Hid Lights Flicker Then Turn Off Remember, a 30mA fuse is required for use with HID components.

Add to Want to watch this again later? Hid Sometimes Doesn't Turn On This usually resets within 3 minutes. Password: Confirm Password: Email Address Please enter a valid email address for yourself.

Check the vehicle's fuses, and make sure they haven't been blown.

ChrisFix 1,669,934 views 8:33 Fixing Strange Auto Electrical Problems - Duration: 4:10. Why Does My Hid Light Go Out To resolve this you will need a wiring harness. This situation can be treated as a matter of "reverse polarity" such that flipping the plug 180 degrees will solve the problem. Halogen bulbs are not affected by polarity therefore some car manufacturer may have their polarity reversed.

Hid Sometimes Doesn't Turn On

What you will have to do is rotate the 2-pin oval connector on the ballast by 180 degrees in order to reverse the orientation of the plug. https://www.ddmtuning.com/support/index.php?/Knowledgebase/Article/View/11/0/hid-troubleshooting-flickering--one-side-working--not-lighting-up--intermittent-firing Email Address: Insurance Please select your insurance company (Optional) Please choose oneAAAAARPAllstateAmicaFarmersGeicoLibertyMutualNationwideProgressiveState FarmUSAANot listedUninsuredNot Saying Log-in User Name Remember Me? Hid Headlight Problems Register Now In order to be able to post messages on the 8th Generation Honda Civic Forum forums, you must first register. Hid Turns On Then Off If everything's hooked up correctly now, just take a quick scan over the headlight housing, the headlight lens, and the positioning of the components to make sure everything's in good working

You'll just need to take some pliers and remove the pins from the connector, which you'll then place into the factory harness in a new configuration. Sign in to make your opinion count. More than likely because the car can’t supply enough power to the ballasts on startup. If this happens to you, shut down your car's headlights, wait about 5 minutes, and then try starting it again. Hid High Beam Not Working

Christian Macias 7,795 views 6:18 Saab 9-3 Xenon Troubleshooting. This can easily be corrected by adding a set of warning cancellers (capacitors) to your setup. 5. XenonHIDs.com (866) 927-9129 [email protected] My Cart 0 You have no items in your shopping cart. have a peek here You may have overwhelmed your vehicle's fuses by installing these HID upgrades.

Hope it works! 03-31-2009, 12:16 AM #4 (permalink) e23k137 Member Join Date: Mar 2009 Posts: 34 Hi, I just checked all my connections to make sure theyre tight. Hid Low Beam Not Working The level of the two sizes' headlight housings are not even, to adjust the headlight housings, please check here. 2. Also, sometimes increasing the headlight fuse by 5 amps solves the problem.

If the noise persists for longer than 10 minutes, or if the noise is more of a clicking sound, pop open the hood and check everything out.

Thank you so much for your advice!!! 03-31-2009, 12:59 PM #5 (permalink) Chip Banned Member Join Date: Jul 2008 Posts: 171 I have a similar problem, but I If you can't find anything, seek out professional advice. JavaScript seems to be disabled in your browser. Hid Stopped Working Neither light turns on: This is almost always due to reversed polarity.

Check the bulb that does not work. If the problem still persists, the Ballast and/or Igniter may be malfunctioned. It is an issue with the vehicle's factory wiring orientation. Check This Out Look inside the connector and with a precision screwdriver you can release the pins and reverse the wires. 3.

One Side Doesn't Turn On This could be caused by a bad bulb, ballast or wiring. Password Register Forum Garage Garage Garages Browse by Username Browse Recently Added Browse Recently Modified Browse Most Popular Advanced Search Help Photo Gallery FAQ Calendar Auto Loans Insurance Today's Posts Auto The problem may be with the entire HID system, or with your vehicle itself. 11. Make sure the ballasts and bulbs are properly connected and secured, and make sure everything's receiving the right amount of voltage, according to manufacturer guidelines. 3.

Make sure the power terminal is properly connected to your car battery and that the wiring harness is securely grounded. 6. You will need a wiring harness to power your HID kit directly from the car's battery. If one side sometimes doesn't turn on it could be caused by a bad bulb, HID ballast, LED driver or wiring. If your car has Daytime Running Lights (DRL) flickering is usually caused by the lower voltage needed to run the DRL at half power.

What this means is the power and ground wires of your vehicle's stock harness are reversed. Your #1 Source For HID & LED Kits Follow Us: Facebook Instagram 45% OFF Daily Deals! Bi-Xenon HID kits have 3 pins on the harness connector for ground, low beam and high beam connections.